Has a rugged 1000 pound capacity to handle most domestic and imported engine, plus light trucks. The 50:1 gear ratio allows for easy rotation of the engine which self locks in any position. The mast folds down with a pull of the pin. When the stand is not in use, it is not in the way taking up valuable floor space. The CG50 can be folded down and rolled under a bench or hung from the wall. The stand can be easily transported to a job site.

The CG50 is an excellent industrial positioner. Can be used for assembly work, welding, inspection - you name it!

BUY DIRECT

Qty. 4 In Stock

General Purpose set for 1/2 Ton Pick-Up Trucks or vehicles with king pins smaller than 7/8". 3" spread between posts with 6-1/2" reach.

 BUY DIRECT Qty. 15 In Stock  4-6 Weeks for Backorders

For trucks or buses with king pins larger than 7/8". Select from the 2", 4", 6", or 8" pilots and use to start the kingpin and push it part way out, change to a longer pilot and finish pushing pin out. 5-1/8" spread between posts with 12-13/16" reach.

Self-leveling action compensates for any helix angle spring. Jaw length can be adjusted. Pulls with equal pressure on both jaws.

Combines a tapped hole puller with two lock plate removers (narrow and wide bridge). Designed to service airbag equipped Saginaw steering columns.

Designed for airbag equipped Saginaw steering columns. This set includes two zinc plated pullers (narrow and wide bridge), and two pressure screws: sizes 9/16"-18 and M14-1.5. (Narrow Bridge Not Shown)

Hydraulic Cone for CG5560HY Hydraulic Tail Pipe Conversion Kit used with Lisle Tailpipe Expander PH300.

Hydraulic Cone for CG5560HY Hydraulic Tail Pipe Conversion Kit used with Lisle Tailpipe Expander PH300.

For removing wet sleeves on diesel trucks, construction equipment, and farm equipment with cylinders of 3" to 6". Reach is 7" to 12". Adjustable bridge fits around studs in block.

Provides up to 6 ton of hydraulic pressure for removing wet sleeves on diesel trucks, construction equipment, and farm equipment with cylinders of 3" to 6". Reach is 7" to 12". Adjustable bridge fits around studs in block. Includes CG80A Wet Sleeve Puller, CG652 6 Ton Power Pack and CG80-21 Hydraulic Pressure Screw.

For bus, truck, or tractor tires. Sliding hammer weighs 13 lbs. Stroke length is 16"; overall length is 46" closed and 62" expanded.

Removes press-fit rear brake drums or any demountable wheel hub from passenger cars and light trucks.   Features: puller jaws can be moved to fit any bolt pattern wthin four to seven inch diameter bolt circle. Puller uses the vehicles wheel studs and lug nuts to bolt it on for pulling operation.

Breaks axles loose on cars and light trucks with flange-type axles.   Features: puller jaws can be moved to fit any bolt pattern wthin four to seven inch diameter bolt circle. Includes ten pound slide hammer with 23-1/2" slide screw and three jaws. Puller uses the vehicles wheel studs and lug nuts to bolt it on for pulling operation.

Features a 2" steel channel frame that bolts to the work bench. Gearing multiplies handle pressure up to three tons of force. Includes arbor frame, utility punch, work block and an adaptor to convert 1/2" drive to 5/16" round drive.  Work Area: 9" between work brackets, 12-3/4" vertical capacity, 9" opening width. Pressure Shaft has a 9" stroke.

To be used with CG100 Arbor Press and Snap On's CJ951 Bearing Separator for Alternator, Generator and Starter Repairs;   Features:  Remove and Install Drive and Bearings from Rotor Shaft, Pulley Removal, Remove and Install Rectifier End Housing Bearings, Diode Installation.

4-Ton Hydraulic Bench Press. Includes frame, ram, pump, and accessories. This unit can be used with the CG101 Attachment Set. Work Area: 9" between work brackets, 12-3/4" vertical capacity, 9" opening.

For Cup and Flat (Disc) Type Expansion Plugs.      Features:  Self Tapping Screw - Screw may be re-sharpened on bench grinder.

Includes two and three way yoke, pressure screw, and adaptor plus four sets of studs. 1-1/4" to 3" Bolt Circle.